uFoscam allows you to remotely monitor up to 9 multiple live video and audio feeds with top notch performance and super easy control for Foscam IP camera.
Unlike the ordinary Foscam applications, uFoscam not only gives the user many more options for operation, but enables to quickly and easily add new models right after user's request through our open architecture software.Main Features
▶ Up to 100 cameras can be configured
▶ Direct access to audio and video streams from cameras. No NVR or 3rd party server is required
▶ 2 Way Audio
▶ Enable or disable Motion detection up to 9 cameras (recommended in quad core CPU)
▶ Automatically record video feeds (No audio) to your local picture folders by camera name, date when motion is detected.
Motion detected videos are saved to your local folders on your Mac as the following naming formats:
Movies -> com.ubn.uFoscam -> your camera name -> your camera nameYYYY-MM-DD HH:MM:SS.mov
(Note) This function is supported in our motion detected software, thus videos are recorded while this software is running on your Mac.
▶ Easily view multiple feeds simultaneously on a screen with layout controls (1, 4, 8, 9 layouts)
▶ Last layout they were at automatically saved (initial layout is 4)
▶ Live video viewing of up to 9 feeds at a time or full screen
▶ Friendly navigate back and forth between multi cameras screen
▶ Pan and Tilt controls up to 8 directions
▶ Set and go presets up to 8 positions
▶ Control an automated vertical/horizontal patrol
▶ Switch IR-LED illumination for night vision on/off
▶ Adjust brightness and contrast
▶ Toggle mirror and flip mode on/off
▶ Adjust video resolution and light frequency
▶ Set the resolution of video image (if applicable)
▶ Enable or disable Aspect Fit
▶ Quickly and easily add new models with reload button
▶ Clone easily camera settings
▶ Reorder camera lists
▶ Enables setup without username and password for a public camera anywhere in the world
▶ Compatible with Dynamic DNS services
▶ Take snapshots or share via email, Facebook and/or Twitter
Supported IP Cameras
PanTilt: FI8608W, FI8619, FI8620, FI8901, FI8901W, FI8906W, FI8908, FI8908W, FI8910W, FI8918W, FI9820W
OutDoor: FI8601, FI8601W, FI8602, FI8602W, FI8903, FI8903W, FI8904, FI8904W, FI8905W
Other: FI8902, FI8902W, FI8909W-NA, H3-186
For FI8601, FI8602, FI8602W, FI8608W, FI8620W, FI9820W, we support only low resolution video with Pan Tilt (not support audio and other features)
The following branded cameras may be also compatible with uFoscam (not sure for audio)
Apexis, Clairvoyant, EasyN, EasySE, Eyesight, Hootoo, Novibo, Smart Teck, WatchBot, Winstar
Refer to detail supported models at www.ubntek.com/ufoscammac
Before you can control your camera(s) remotely over data networks, you need to setup your router to allow incoming traffic. For security reasons, routers don't normally allow external traffic into your local network. You should read your camera's setup manual regarding port forwarding. For more information, please see www.portforward.comor www.dyndns.org
The quality of video display(s) shown on your device may vary according the quality of the camera(s) and the data received from them.
The response time of PTZ control and multiple cameras view depends on the network and/or your device itself and/or camera capability which may cause a little bit of delay in feedback.
Simultaneously continuous capturing videos by maximum motion detection enabled may cause increased video frame and audio delays.
If you have any questions or comments, or you would like to request that we support additional camera models, please send an email to firstname.lastname@example.org
uFoscam (com.ubn.ufoscam) is a Mac software application that has been discovered and submitted by users of Software.com.